When one gets a run of continual improvement going it has a sort of magic of it's own. Each time out there is the dual hope that it will continue, and fear that the bubble will burst, and the streak will be broken. I have a streak of improvements with each event this year, and as a result I am already bursting through my wildest expectations at the beginning of the year.
Two events ago, I went into the event, more or less having achieved my goals for the year, with several events putting me in the top 20-25% already. Then I ran 22nd of 139, just one place (and 0.091s) short of my top 15% stretch goal. It was fabulous, but how on earth could I top that? How do I keep the streak going?
Well, my tires were mostly toast, ending the last event at 120 runs and 138 after the last renegade event. The 70 run tires I took off just before the tour went back on. Changing setup and car balance during the season can be disastrous, if the car behaves different and you can't adapt, cones and slow times will often result. But, I was facing elimination in the points race. If I lost, I would be mathematically eliminated and the final event of the year would amount to a test and tune/fun runs. With this in mind, I decided to fix the front splitter.
Over the course of the season, the plywood splitter I had added had become warped. Attached at the front and the back with foam to seal the air in the middle, it the middle was bowing downward, and the car had started to push. Both Ben and Brian remarked on it, and I felt it too.
This warping is a result of my insistence on not attaching the splitter to the fiberglass. Attaching to the frame in the back with supports on the front was fine when I was using a carbon fiber splitter, but not so fine with plywood, especially after it got wet. I needed a stiffener. I didn't want to add more aluminum angle along the bottom. The front already scrapes on the occasional curb cut if I'm not ultra careful about where I drive. Adding something that hangs down further would not work, and of course I always want to minimize the weight. Thin, light and stiff made me think Carbon Fiber. I found some economy 5mm 6"x30" carbon fiber for under $100. 5mm CF is rock solid. When I got it I could barely flex it at all. So I applied that along the top, eliminating the aluminum bar that hung down in the middle previously
I probably gained a few ounces, but I only have the "feel" of it since I forgot to actually weigh it. In any event it worked marvelously...
Much straighter, much tighter to the bottom of the car. But would it mess up my driving, or help it?
SCCA points Event #8 was a cool, blustery day to start, Morning runs for the 3rd run group were in the low to mid 60's. My first run was messy and slow. On my second run I spun in a slalom, but I got a good practice run at the finish. Both Dan and I noted that the car felt different and that the push was reduced, or maybe gone. Sounds like a disaster in the making...
BUT here's where the seat time this year paid off. I didn't panic. Instead I set about trying to figure out how to adjust my driving. I said to myself... "If it's not pushing at high speed anymore, that means I should be able to nail the sweeper hard. I need to set that element up so I can take advantage" and I also said to myself, "I need to be extra careful on my entries to the slaloms...." My 3rd run of the morning was faster and clean... and came in just 0.4 sec behind Leafy, whom I needed to beat to remain in the hunt for a season championship.
While I was fairly happy with the first part of my 3rd run, I knew that the finish had been a near disaster. I had become late on the angled walloms, and then been forced to focus on controlling the car rather than putting power down at the finish. I only just barely touched the rev limiter at the finish line. When I checked the numbers, my run was fairly decent. After the rest of the morning runs finished. I was 2.8 seconds off top pax, which usually equates to a top 30 finish. But of course folks will find time in the afternoon, so I need to find time as well. I said to my co-driver Dan, "I need to put the finish of my 2nd run on the first 3/4 of my 3rd run."
Then came the afternoon runs... Temps were up by about 5-10 degrees. The tire blankets were not needed, but it was still cool with somewhat less wind. On my first run, I more or less did what I set out to do. I pasted together the front of run 3 with the end of run 2, and managed to find half a second, enough to put me in the lead vs Leafy's morning time. But I knew that Leafy would likely find time too. Reviewing the run in my head, I decided that I still wasn't working the first part of the course hard enough.
On my second run of the afternoon I found another .8 seconds which firmly cemented my lead, but I FORGOT to turn on video! DOH!! However SoloStorm did start it's data logging, so here's a video of my 3rd run of the afternoon which was as fast or faster than my fastest until I botched the finish (if you ignore the cone). Overlayed on that video is a video of the solostorm comparison playback with my fast run (run 5). The paragraph that follows is my from memory description of run 5 (not 6 which you see in the video)
So here's my "in-head video" of run 5, (the green line on the above video):
I made a more agressive start and it felt good but I slightly under broke in the turn before the big sweeper, so my sweeper was a tad slow, however I kept my foot in and built good speed, barely taping the breaks to get through the following slalom. As I did so, I realized I probably didn't even need to touch the brakes, and I felt I slightly over broke on the turn towards the taxiway too. As those thought flitted by, I immediately said to myself, well if I'm a little slow, I should be able to get a good turn onto the taxiway to compensate. I remember feeling that I did a good job of the turn, but didn't really get on the gas until the end of the taxiway. The surge of power as the cams kicked in at the end of the taxiway reminded me of some other times I had overshot breaking points, so I laid into the breaks as hard as I could, and then let off and just turned the wheel where I needed to and prayed it stuck. It did stick, but just barely. The back end slid just a tad and then hooked back up, putting me in a pretty good position entering the main runway. Even as I was noticing this, I found myself thinking "GREAT, lets take advantage of this!" and I accelerated out of the turn as hard as I could. This actually put me just slightly shallow on my entry to the first slalom on the runway, but I realized I was not getting a great entry and with a quick stab to the breaks managed to rotate the car and get in half way decently anyway. I knew I was immediately facing a cut back across the runway at the end of the slalom, so I only fed minimal throttle to avoid making that turn too difficult. This worked well, and I got a more comfortable entry into the second slalom. With a good position on the second slalom I was able to be on the accelerator at the cone before the end of the slalom and gained a lot of speed through the slanted six pack. Much like the exit from the taxiway, this left me slightly shallow and I again compensated with a stab of the breaks. Then through the walloms I worked on being patient and getting ahead of the cones in preparation for the finish. I was able to mash on the accelerator and I knew I was going to be all over the rev limiter so I tried to go to third and missed (oops). As I crossed the line, I wasn't quite sure how I had done, it felt clean and fast, but I'd been so busy thinking and adjusting through the run I wasn't sure. When the display read 50.9 I was shocked and elated, and prayed it was clean, which it was.
In retrospect this run was a huge achievement, but not because of the time or the PAX position. It was huge because I had retained focus, and adjusted on the fly effectively. In essence, I had successfully implemented the advice Eric Chiang had given me a year and a half ago. I drove the car as it was on course. I drove based on the feedback the car was sending through the steering and the seat of my pants and by the status that my looking ahead was giving me. A year and a half ago I was falling prey to driving based based on my expectation of the course. Eric had noticed when he road with me that I accelerated in some spots beyond what made sense, and guessed correctly that I had been thinking to myself "I should be fast here, I should get to the rev-limiter." He said it was a common problem and hard for some people to overcome.
I also felt that the run was a huge achievement in that I went from coning and spinning in a car that was doing new, strange things to running my best time ever within a few runs. Even better, it's easy to see from the above video that there was more time out there 50.4 seems very doable, and that would have been top 10 (just barely)!
Here's my thought on all of this... the big thing that seat time gets you is a familiarity with driving at speed. It brings instant recognition of "Oh crap, I'm getting too fast, brake hard NOW!" (e.g. at the end of the taxiway), and the calm analytical workaround of stabbing the brake to help rotate the car on a less than ideal entry. It allows thoughts about where to go faster next time without becoming disappointed or distracted, and it allows you to find the silver lining when you are slightly slow and just keep driving... I finished that run, my fastest ever, and I didn't have the shakes, I wasn't out of breath. I had remained calm and focused throughout, and that's probably why it was possible. Without that calm, the success of the hard breaking would be wasted on relief that I escaped disaster. Without that calm, the timing of the break stab would likely be early or late doing little good at all.
And as I said in my last post... drive fast, and the points will follow. I won first place and I remain alive (if just barely) in my hunt for a season championship. I think my driving at this event this event was championship level driving, but alas, I was not driving like a champ at the beginning of the year. I have to hope that someone beats Leafy, and I beat them. With a result like today, where I was almost a second ahead, it seems like a possibility, but very very far from a certainty. I'll give it my best, but smarter money is on next year at this point.
I really hope I can keep my cool like that in future runs. The results are waaaay cool :).
Last winter I shifted my splitter forward 2 inches to try to get more front down force, but it seemed to have a very limited effect. This is probably because the main protrusion of that splitter is just in front of the radiator grille. The air flow in the radiator and up over the car is not very significantly restricted, and less so with the AC condenser removed. Thus, the increase in pressure over the splitter vs under is probably minimal there. The sides gained extension too, but the sloped, drag reducing front of the car is probably also fighting the build up of pressure as well.
Since I improved the wing over the winter, I expect to generate more downforce in the back. To make use of that added downforce I will need more front down force. Otherwise I will simply go back to the car plowing on the fast sweepers. To that end, I've ditched the CF splitter and cut myself a much larger plywood one, similar to that used by the other street modified cars in my area. Here are some pictures of the construction process....
Jack it up, prop the board underneath
Scribe a 5.75" offset from the fender (viewed from above). The rule is 6", but leave a bit for safety and interpretation etc.
Painting with Rustoleum to give it a little water resistance...
Initial attachment. The sides still need trimming, they stick out a little bit too far.
View of bottom attachments. As always I am attaching to hard points, not the fiberglass clam
If air passes above and below an added aero dynamic aid it is considered a wing. Front mounted wings are disallowed in the super street modified class, so trim the ends and put a back plate in to turn it back into a splitter
Another view. It's hard to see because of the paint, but Aluminum angle is used to attach the backplate
The final result from the front
The edges ere a bit floppy and I didn't want to attach to the fiberglass, so I rigged a turnbuckle system attached to the oil-cooler mounting point which is steel.
A slit in the fender liner is required. Re-installation is quite a trick since the top part of the fender liner is actually supposed to slip in first, but that is no longer possible. Really glad that i was conservative on the size of the back plates.
Ever so conveniently the vent for the oil cooler accommodates the turnbuckle!
The result is that the turnbuckle system is not 100% rigid, so I may need to re-work this if the edges wind up flapping, but it should also work to dissipate and absorb some of the energy from cone impacts. The great thing about this is it was really really easy to install and provides a bit of adjustability if the corners turn out to be pulled upward by the tension (which is not legal if it's more than 3 degrees from level)
I am always obsessing about weight savings. Maybe it's a side effect of owning a Lotus. Perhaps I am haunted by the ghost of Lotus founder Collin Chapman who said "Power makes you faster on the straights, lightness makes you faster everhwhere." (I wish he would haunt my driving skills a little more and my wallet a little less!). I seem to find inordinate joy any time I can save weight on my Lotus and revulsion deep in my gut any time I have to add weight.
So I'm sure you know where this post is going... :)
This winter I'm looking to shave another dozen or so lbs off of my already featherweight car bringing it close to 1850lbs with 1/3 tank of gas. That 1/3 tank probably weighs 15 lbs or so, which means even if I'm out of gas I will be 30lbs over the minimum weight for my racing class, but here's what my mania has produced to achieve the latest reduction.
The Battery
Batteries are heavy. They often contain lead and lead is heavy. Long ago I switched away from the stock battery which is a 29 lb. monster. That size is mostly needed to support the drain on the system caused by the vehicle alarm system. The little 4 cylinder 2ZZ motor in the elise definitely does not need that kind of capacity to turn over. So 3 years ago I installed a cut-off switch and a 7lb Braille battery. Great! 22lbs saved! Seems good... but not good enough! (I did mention that I might be possessed didn't I?). Enter the Antigravity Battery brand XPS SC-1.
I've known for some time that lithium batteries are much lighter, but the products available have generally been too expensive. The SC-1 advertises as 12 oz, but my scale says just under 16 oz. If it works I'm not going to complain. The question is... will it start? Too cold to take the car out so I haven't installed it yet. But if it does the job, I get to save 85% of the weight vs the Braile B106 I'm using now, and it's cheaper too! All I need to do now is figure out how to mount it... I'll make that a separate post.
Lightness Added: 6lbs
The Wing
Ever since I built it I knew that I had added a tragic amount of weight when I added the wing. It adds and estimated 25lbs, much of it at the very top of the car, raising the center of gravity. about half that weight is in the supports and attachments to the deck lid. The wing itself weighed 13 lbs. (excluding mounting bolts) when I weighed it a few weeks ago. The construction was entirely 1/8" 1x1 Aluminum Angle, 090 plate aluminum, a 1-1/4" wood dowel for the front edge, steel angle brackets and aluminum rivets with a contact paper skin. I'm actually quite pleased with the contact paper, and the aluminum rivets are probably as light as i can get without a tig welder and a lot of practice time.
After observing the wing in action I believe the 090 aluminum end plates, the wood dowel and the aluminum angle are all over built, or just poor material choice. These are being replaced by much lighter components. The angle is being replaced by 3/64" 1x1 angle (available at Home Depot).
The front rod and end plates are being changed out for carbon fiber. Carbon fiber is not cheap, but I found a discontinued size I can use directly at a steep discount. The end plates won't be as big as I would like, but they will be a little bigger, and the cost is about 1/3 the cost of buying a larger piece in a standard size and cutting it down.
There's a bit of a problem in that I need to have good supports for this CF tube at the front and I need to butt join it to the end plate efficiently. Luckily, I have a friend who just bought himself a Maker Bot 3d printer, and he pointed me to the free OpenSCAD program which renders 3D objects defined in it's own programming language. Since I've got my own software consulting business, this programmatic style is perfect for me. Here are the supports rendered in OpenSCAD
And here are the inserts for the end of the tube (view from inside tube)
So what sort of weight savings does this buy me? Well here's how it works out (orange values are estimates):
Before
After
qty
endplates
398
240
2
front rod
784
155
1
fastners (all)
450
450
1
center supports
130
130
2
spars
606
275
6
total (g)
5,926
2,995
total (lbs)
13.04
6.59
lbs/sqft
1.65
0.83
saved (lbs)
6.4482
50.54%
I haven't accounted for the printed parts yet, but they are very light and will probably be offset by a few of the steel angles that I was able to trim down. About 5 oz. was also removed by trimming corners and overhangs from the bracket that mounts the wing to my deck lid.