Showing posts with label repair. Show all posts
Showing posts with label repair. Show all posts

Tuesday, July 3, 2018

New Heights, and New DIY

Once again, I've been slacking on the blogging, but as you will see on the standings page, the season has been progressing, and I've got a co-driver who's giving me some solid competition. The first few events were Freezing, Soaked and Soaked, so I pretty much lacked anything inspiring to blog about anyway. I went to the new Jersy Pro Solo, and had not really found my stride after missing most of 2017 in my car and getting almost nothing but rain events in the early season. I just wasn't getting slip angle like I should, and I was quite dirty, hitting cones or red-lighting on many of my runs as well. As will happen at the national level, if you aren't in top form you're at the bottom of the standings...

Some how I didn't feel eager to write about that either...

However, the weather improved, and satisfactory driving has finally come to pass. I've now managed to regain my prior level of driving from 2016, and in event #5, I finally found a new high point. One of the tough things about evaluating one's performance in autocross is that all measures are relative and the reference point is constantly in motion. To make a sane evaluation one has to make some assumptions. My first assumption is that the top drivers in our region are not getting slower. Given our region's consistent 6-7 national champions the last 3 years this seems reasonable.

While I'm comfortable saying that the top of the heap is still at a high altitude, there are some other things that clearly have changed. Firstly our region has had a buble of talented drivers mature in the last 2 years. I'd not want to argue that any of them have really pushed the top of the pax standings up yet in the way that Billy Davis did in 2015 and 2017, but they have definitely crowded the top. In 2016 I had 3 events where I was 1.5s off top pax, which resulted in 15th, 10th and 15th in overall pax. This year at the last 2 events, 1.5s from top pax is worth 20th and 19th... So making the top 10 or top 20 is significantly harder than it was 2 years ago.

Secondly, pax for the SSM class has been hit harder than any others besides AM, BM and CSP. BM/CSP and SSM are all almost a full percentage point harder than 2016 relative to the other classes. This translates into about .44 seconds tougher pax on a 60 second (raw) course. I've made a spread sheet here that shows that while all pax factors (other than AM) went down, the average pax factor went down much slower for SSM. This probably has something to do with the last 3 champions Thorne, Glagola and Wilcox all hanging out in the top of pax at far too many national events...

With that in mind, the 20th in pax result that had me 1.5 seconds off of top pax in event 5 Looks a lot like what used to get a top 10 in 2016. And my 2.3 seconds off of top pax in event 6 looks a lot like a top 20 in 2016 even though it now shows as 30th. Kudos to my co-driver Daryl, who kept the car in the top 20 at event 6 with his 19th in pax. For 2 events running my car has been 2nd fastest car with doors. Here's a video of my 2nd fastest run from event 5, which is probably faster everywhere except the start where I forget to shift like an idiot... Sadly I didn't remember to turn on the camera for the fastest run.


Additionally, I've also done some more maintenance/improvement on the car. Another factor in my bad results at the New Jersey Pro solo was epic levels of wheel hop on my launches on day 2 when the rubber was creating a lot more traction. A lot of exhaust bounce had also been noted at Devens, and the result was too much for my front motor mount to take.



The alignment was checked and it was almost 6mm toe in, probably due to bushing migration. Soft bushings, lots of toe-in and enormous race tires are a recipe for massive wheel hop. There was only one conclusion, tired old plastic/rubber A-arm bushings had to go. I replaced them with Monoball metal/teflon spherical bearings from Inokinetic. Since this seemed like an interesting job, I also made a DIY video for it:


The results? FABULOUS. Both me and my co-driver Daryl noticed improvement in the predictability of the back end when rotating it around a corner, and improvement in braking. The first was expected and the second was a nice surprise. My rear suspension had probably become so floppy that the ABS probably triggered earlier. I also suspect this slop negated all rear braking once it triggered by wagging the A-arms back and forth with the ABS pulses. The start for this course did not lend itself to hard launches, and due to the late date of it's discovery I had to continue with the above mount after Ryan welded the split for me. Next event we will be doing full launches if the course allows it and then I expect to find that the wheel hop has also improved.

Sunday, March 11, 2018

Transmission Oil

Transmission oil is easy to forget about. This winter I realized that I probably had let mine go a little longer than I should have. It probably should be changed at least once a season on a car like mine. My car sees 20 autocross races a year at an average of 8 runs per event and almost a mile per run.

That's not an official service interval of course. There are no "official" numbers for racing since everything "depends" on the duration, level and type of racing. On a race car, nearly every bit of maintenance needs to be done a LOT more often than with street driving. So for another example I change my oil about once every 6 auto crosses, which works out to about 3-4 times a year, or in terms of mileage, about once every 40-50 miles of racing... Similar to changing it after every 1-2 track days.

Fluids are cheap the parts they lubricate are expensive! Buy good fluids often, because that's much better than buying cam shafts, engines or transmissions! Also,  you never miss a race because you had to do an oil change... failed parts however frequently cause missed or aborted racing.

For something new this year, I decided to try my hand at vlogging and produced a video that might be helpful for those who want to avoid a trip to the mechanic, save some money and change their own transmission oil.

This is not a difficult job, but of course I am not a trained mechanic, and you should use your own caution and do your own research before attempting any of this on your car (especially if it's not a lotus!) If you see something I could do better, leave a comment on this page or on the video.


Some additional commentary and advice here: http://www.lotustalk.com/forums/f25/transmission-oil-change-445914/

Monday, December 25, 2017

Return of the SoLoti

So yeah I got tired of blogging about how my car wasn't working... probably you got tired of hearing about it. Then when I finally got it working in September I spent all available weekend time driving it rather than blogging about it. I had a little bit of pent up racing to let out! Then I took on a new client and have had 1.25 people's worth of work to do...

So what's the story? Well, After waiting forever and then some for a valve tool to arrive at the shop that did the install of the head that was supposed to make it easier for him to check on the valve seals, I lost patience and took the car to MC racing, and they hooked up a compression tester and a leak tester, and whoosh... air in one piston and out the other... Clearly the head gasket was not sealing properly. Perfect proof that it is so very good that Nick my tuner at Ace Performance refused to tune with the car as I delivered it the first time. Kudos to them!

With this new information I contacted the original shop and they started pointing out that I supplied the head gasket etc... basically preparing excuses to not make it right. That sucked but there is of course enough gray area for them to avoid the work if they so chose. Fighting over it was clearly not a productive route to go, so I took it back to MC racing and for 2/3 the cost of the previous shop they took it apart, machined it, provided a head gasket and re-assembled it in working order. There's still a slight bit of smokiness, but nothing like before, and unlike before, when things warm up the smoke goes away. I suspect some things are not quite perfect due to the previous install, but now it's close enough that the thermal expansion completes the seal as the engine warms up. I'll be analyzing oil and keeping an eye on it going forward. If I ever go to high compression pistons, it won't be on this block/head combo.

Speaking of oil, I've moved to red-line 40wt race oil now that the car is a full time trailer queen and never does more than idle around before it's fully warm. In theory this allows a slight hp gain and better flow when warm, at the cost of a little more flow resistance (and thus wear) during startup. It's also the case that with a trailer queen, it is a lot harder to just bop on over to get an oil change, so I'll be moving to changing my own oil and brake fluid. To make that easier, and to help combat the flow resistance at low temp, I went to a Canton Racing  spin on oil filter which gives me about 3 times as much flow as the stock filter and 8 micron filtration.

I know what you are probably thinking... the man dumps umpteen zillion dollars into head work, ecu and tuning and he's blogging about his oil filter?? Point taken...  I'll get to the good stuff now.

So with it back together and (mostly) not smoking, tuning was possible, and the results are very pleasing indeed!


I never had a chance to get a baseline, so the above plot shows the results vs a stock plot I grabbed from the web and scaled to match. These numbers are a couple HP better than any other normally aspirated plot/numbers I've been able to find for cars running stock compression. And these are with the super trap on! Based on a single test run, there's perhaps another 2 hp in it if the super trap is removed. I only have good things to say about Nick's tuning, and Baer who runs Ace Performance was straightforward and easy to work with. I'm very happy to be promoting them on my wing plates!



The Emtron Ecu installed by Ace Performance has all kinds of super nifty logging and capability. No end of parameters to ponder! Below you can see the data, possibly even from the above photo. The slalom in the photo would correspond to somewhere around the 6000 second mark below, but I cant' be sure if it's exactly that run or not.



And I also got a beta version of CAN bus support for the stock dash, which so far seems to work great! Nick/Ace/Emtron will be coming out with new info on their products soon and when I'm allowed to share some stuff I've seen previews of, I'll post it here. Until then, we'll all just have to visit the garage, glance out the window at the snow and sigh... And comb through data logs :)

Wednesday, June 10, 2015

Like LSD man...

Ok sorry for the goofy title, I couldn't resist. So after doing all the work of pulling out the transmission, it became very clear that I want to minimize the number of times I do this. It's sort of fun in a way, but it really does take a lot of time and effort. So besides replacing the tattered, clutch that was probably a hairs breadth from grendading like this one:


The flywheel, and the Limited Slip Differential (LSD) were also installed. Basically, as a consultant, my time can be converted to money fairly readily and long term it's cheaper to do it all at once.

The flywheel is the Fidanza Aluminum flywheel, which shaves 6.8lbs off (about 45%) the stock. The clutch plate itself is only an ounce or two lighter, but it has less mass near the edges, and the clutch plate cover and pressure plate is a pound less, so the total weight savings should be about 8lbs of rotational weight. 

The LSD will offset that somewhat, adding back a couple pounds or so, but the diameter of the added rotational parts will be small, so perhaps 5-6 lbs off the car, and even more reduction in rotational inertia. PLUS power will now be available in the corners!

Only one problem... with great power comes great responsibility. It turns out that a lot of the time I've not been very gentle with the throttle. The LSD exposes this flaw in my driving in 2 ways. First, if lateral grip is not at maximum, but the car is turning, when the LSD locks up, this results in power only on the outside wheel (since the axel has become solid the inside wheel with less weight and traveling a different radius must slip). That tends to torque steer the car into the turn. This is potentially useful, but also throws you off if you are not used to it. Second, if you are at the limit of lateral grip, adding power now causes the OUTSIDE rear wheel to slip... and that will tend to make the car want to spin.

So while the LSD unlocks a new level of potential speed, the open diff will tend to save you from yourself, and is slightly easier to drive. My first event on the new LSD was quite disappointing because I was discovering that my throttle work needed work. After about 5 events, now I'm getting used to it and learning to ease onto the throttle and not be on/off the throttle as violently, and may just be beginning to reap the benefits of the additional speed in the corners.

Other notes on the changes I made... the lighter flywheel seems to make it slightly harder to get the car to actually turn over, which puts my present battery solution right on the very hairy edge... I probably need to think about setting up a cold weather jump system to ease the wear and tear on my starter when I have to leave for a race in the early AM. Mostly I just need an easy way to get jumper pack clamps on the battery.... without risking a short. The present space is pretty tight.

Monday, March 16, 2015

Waiting for the thaw...

Such a winter... 3-4 ft snow in the yard at max. Many all time snowfall records broken, season record in jeopardy. Even more amazing, it went from almost zero to nearly a season record in under a month. Not much was happening in early winter, so I didn't bother trying to manufacture a post. Then later, I was preoccupied with climbing on my roof to hack off the ice that was almost a foot thick in places...

With winter wrapping up and warm weather on the horizon, of course the car is somewhat disassembled... So I don't have time to write anything interesting now either, but I can offer you some pictures of lotus guts...






So obviously, the clutch is getting replaced.... other mods TBD, time/$ permitting...

Tuesday, June 5, 2012

Here We Toe Again

Setting the toe was a bit of an ordeal. First I had to master setting up a home made string alignment system, Then I had to actually properly set the toe. However, given that I had 4mm of front toe-in, either I do it myself, or pay someone to do it.

The string alignment system I used is detailed on Lotus Talk, but I deviated slightly. First off, I cheaped-out, and bought one $9 length of 1/16th inch aluminum U channel instead of 2 1x1x1/8 aluminum angle ($21 each). I saved $30 this way, but I'm not sure it was worth it. The flimsier channel flexed a little, requiring a little extra re-measurement and fiddling around to make sure everything was straight.

So once I got the strings set up, and figured out which way to turn things, I removed all front toe-in. The car drove somewhat more nicely on the street and I did well at my first event. However in putting the tires on for my second event I noticed a rub mark on the frame. Honestly I'm not sure if it's been there all along, but there seemed to be some corresponding signs of rubbing on on of the front tires, so I made a quick in the field adjustment to add 4mm of toe back in with the gracious help of my competitor Matt (lent wrenches), and PJ (lent jack stands). I ran the race, but it felt a little bit tail happy, and even more tail happy back on a faster course at Devens for the third race.

The (possible) rubbing was on the inside rear of the front left tire. The initial theory I had was that the wheel had rubbed when I was cornering hard left around a pin cone in the first part of the course, and accelerating, thereby unweighting the front left corner and allowing the wheel to droop. Liberally applied crayon to the rubbing area so I could tell if it rubbed again. It did not, and I was relieved, since I REALLY don't want to rub a weak spot in the frame. That would be dangerous, and even if I didn't experience a direct failure, it would force me to total the entire car.

However, after the third race I spent some careful time looking at the rub marks and the wheel, and I noticed a few things. The wheel had little strings of what looked like peeling off in the rubbed area, and the wheel weights had an odd-safety orange color to them. I pulled at the strings and noticed that they appeared to come off, and appeared to be added on to the surface of the rubber, not part of the rubber itself. Also the stringy bits didn't seem to stretch much at all, not what I would expect from bits of tire rubber, more like plastic. Hmm... what's orange, and plastic at an autocross... hmm... sounds familiar... hmm... CONES! I distinctly remember having a cone caught under the left front wheel on one of my runs in the first race.

So now I believe that the rubbing on the wheel and maybe the marks on the frame came from a trapped cone, not wheel contact. However, I'm cautious about leaping to conclusions here, so now I've dialed back out half the toe-in (giving me about 2mm front toe-in), and also stiffened the front shocks 2 clicks to (hopefully) help with the over-steer.

The NCR Porsche club event on 6/2 was a soaker, so I never put the race tires on, and never got a good test of the new settings. I'm hoping for better this weekend with Renegade Miata... right now the weather man is saying it will be dry, which probably means it will rain....

Thursday, March 29, 2012

Yes We Camber!

Now that I have a fresh new U-joint in the steering and the winter gas is all burned off, it's time to get ready for racing. This year I intend to work hard to ensure that the camber and toe are properly set, the car is corner balanced, and I hope to work out the best settings for my shocks, sway bar and tire pressures in light of the new setup.

That's about a six variable optimization (if you don't count weather & temperature), which is kind of daunting. Where does one start?

While I was doing the work on the steering, I noticed that my right side had a lot fewer camber plates than the left, so I had a strong suspicion that my side to side camber was not correct. Therefore, since this appears likely to be out of whack and since the settings are available on Lotus-Talk, I'll start there.

Over the winter, I bought a SmartCamber tool, but before I can use it I need to get the car on a level surface and equipped as if it were racing. We want to optimize for racing so the setup will be slightly off for road use, but road driving isn't a competition (despite what the folks in the urban assault vehicles seem to think).

I put on the race tires, removed the tow bar and put 150lbs of books and break rotors in the driver's seat to simulate the driver (which is around 7% of the weight of the car!). To level the car, I shimmed the wheels with linoleum tiles (available for 69 cents each in Home Depot). I measured how many each wheel needed with a 78" long level resting on a couple of sockets and the SmartCamber tool, which is really just a fancy level. After marking the point I measured the tiles, rolled the car to that point and jacked it up. After jacking the car up, and placing the tiles under the wheels I also inserted a plastic bag folded over with some motor oil between the folds. This allows the tires to slip sideways when the car comes back down and avoids the need to roll the car back and forth.

The camber measured -1.1 on the right side and -0.1 on the left side. That's a whole degree of difference, which may go a long way to explaining why my car tended to ABS earlier than it should in threshold breaking. Also, thinking back I can't remember any spins that were clockwise. I hadn't thought about it before, but I suspect that the setup I had settled on in terms of shocks/tire pressures and sway bar settings last year was flawed. Possibly, the right side of the car was slightly tail happy, but neutral on the left, which would be consistent with a better camber setting on the right that gave the front right more traction in a left turn than the front left had in a right turn.

The rear was better, -2.0 on the right, and -1.7 on the left. The latter is stock and the former is just a little bit less than the recommended setting for autocross which is -2.25.

I took out all three shims on the front left, one on the right rear and two out of the left rear. The result was -1.0/-1.1 in the front and -2.1 -2.3 in the rear. This is now within the .2 side to side tolerance recommended by Lotus (just barely for the rear). Many serious racers seek even more negative camber in the front, but to achieve more one needs to replace or mill the steering arms.

Anway, Next up... Measuring the Toe. Here are some pictures of my setup...

Friday, March 9, 2012

U-Joint Install

In a previous post I promised to describe the lower U-Joint install. This was before I understood the depth of this undertaking. I am now in the middle of it (and an additional repair I found along the way). It turns out to be necessary to unbolt the entire steering column and shift it by an inch or two. I don't want to give folks advice on working in the vicinity of the airbag system, so I will only list some general guidelines as to what is entailed, and not a step by step process. The idea here is to help you understand whether or not this project exceeds your mechanical ability or available time frame, not to provide a guide. Things you must do include:

  • Removal of the bolts for the u-joint shaft where it attaches to the steering rack, and the upper U Joint. This will be very difficult if you are overweight, or taller than 6 ft. If getting into the car is difficult for you, this may be physically impossible.
  • Removal of steering column shrouding, and the binnacle over the instrument cluster.
  • Removal of the instrument cluster, and switch pack
  • Unbolting of the steering column.
Please consult the lotus manuals, or other resources for details and safety precautions. I STRONGLY suggest you read section WD of the service manual on airbag safety. I have purchased a copy myself. Working on any part of the vehicle containing pyrotechnic safety devices (i.e. airbags, and seatbelt pretensioners) without the service manual is very dangerous. Note that in the Elise BOTH airbags will deploy and the seatbelt pre-tensioners will also fire if the system is fooled into thinking a crash has occurred. Static electricity can also set off airbags, so proper disablement is important.

Things you don't have to do that I did:
  • Loosen the steering rack - I thought I might be able to avoid moving the steering column this way, but it is insufficient to allow removal of the U-Joint.
  • Take apart the whole dash board. I did this following a thread on Lotus Talk (see links page), but when I got a copy of the manual, it became clear that the dash could be left in place. However, dash removal is not that hard, and it makes getting to the back bolt of the steering column a piece of cake. 
  • Remove the Steering wheel from the steering column, although it's not hard and makes access into the dash to remove the rear steering column bolt much easier. This requires airbag removal however, so I repeat... 
Please READ section WD of the manual before working on the dash or steering column! Airbag Detonation can cause serious injury or death. Also note, that for dash removal you have to break 4 clips on the passenger airbag cover, and that you must buy new ones to replace them. They were only about $10 for all 4 (plus shipping), but you cannot re-assemble the dash without them.